Quantcast
Channel: [EN] Enduser support
Viewing all 10561 articles
Browse latest View live

Image for Duo 4K SE

$
0
0
Hi OpenPLI Team,
 
I've pre-ordered a Duo 4K SE and would like to know the availability of the OpenPLI image for this STB ?
 
Thanks,
 

 

Francois

HD51 huge multiboot problem.

$
0
0
I installed 7.3 RC multiboot on my HD51 today. Unfortunately the multiboot selector does not recognize any other images on the flash not even itself. I have a no images found message on the selector screen. Even FlashImage is not working well. All slots are flagged as empty, even if you flash another image on another slot you still get the no images found message.
What could have happened?

Στάλθηκε από το Redmi Note 5 μου χρησιμοποιώντας Tapatalk

Time change to 12h format (am/pm)

$
0
0

Receiver: VuPlusZero4k, Openpli 7.3
Q: To all knowledgeable members and Openpli developers.
I am moving to North America. Need to change the receiver time to be 12h format (am/pm). Could not fined anything in the expert settings.
Please advice what files have to be changed, how to do it and if this is possible. Everything in the skin xml file was changed, but EPG is still 24h format.
Thanks to all.

Attached Thumbnails

  • Clok_to_am_pm.png

Slow zap on Vu+ Duo 4K

$
0
0

Doing a channel change on Vu+ DUO 4K takes long time and brings up message "Tune failed!". The message comes after approx. 4 seconds and only show shortly, because shortly after that the tune is done. I'm using own build image (develop) from 28 February. Is this a known issue?

 

PS. With OpenVix a channel change is done quicker, approx. less than 2 seconds.

Front screen LCD problem on GB UE 4K.

$
0
0

Have installed 7.3 on one of my Gigablue box. It's a Ultra UE, working perfect, way better then the I have tried. But there is a strange problem, the lcd (front screen) is not working good.

Under boot, everything is as normal, when looking at a channel, the screen gives a tiny tiny clock, but once a while shows the channelname, clock and so on as normal, but just for 1/2 sec. About 2 times a minute. Same as when I go into different meny on the box, the lcd screen seems to be working fine, but just for 1/2 sec every time.

 

Have tried a couple of skins, don't seems that the problem is there.

 

Any idea?

System time error bootloop

$
0
0
Hello,I have two images on my device Open ATV and OpenaPLi .... I installed the latter a few days ago .... Today i got myself on a bootloop when I switched from open Atv to Open PLi ....how can I solve this...the remote isn't responsive when I try to change images.

Vu Duo 4K HDMI input transcoding with streamproxy

$
0
0

Hi all, thanks again for the stable OpenPLi images.

I am trying to use HDMI input transcoding using a Vu Duo 4K 192.168.1.2 and an Xtrend ET10000 192.168.1.3, both running latest 7.3 images.

1st case: ET10000 as server, port 8001: When Vu Duo 4K HDMI output is connected to Xtrend ET10000 HDMI input, using VLC as client on a pc, both streaming from the ET10000 http://192.168.1.3:8001/8192:0:1:0:0:0:0:0:0:0: and transcoding http://192.168.1.3:8001/8192:0:1:0:0:0:0:0:0:0:?bitrate=3072000&width=1280&height=720&aspectratio=2&interlaced=0 work fine.

2nd case: Duo 4K as server, port 8002: When Xtrend ET10000 HDMI output is connected to Vu Duo 4K HDMI input, again using VLC as client on a pc, both streaming from the Duo 4K  ( http://192.168.1.2:8002/8192:0:1:0:0:0:0:0:0:0: ) and transcoding do not work ( http://192.168.1.2:8002/8192:0:1:0:0:0:0:0:0:0:?bitrate=3072000&width=1280&height=720&aspectratio=2&interlaced=0).

Logs of streamproxy and enigma2 from the 2nd case, Duo 4K as server:

Streaming

 

streamproxy

 

streamproxy: accept new connection on port 8002, default action: transcode, fd 6
ClientSocket: header[accept]: "*/*"
ClientSocket: header[connection]: "close"
ClientSocket: header[host]: "192.168.1.2"
ClientSocket: header[user-agent]: "Enigma2 HbbTV/1.1.1 (+PVR+RTSP+DL;OpenPLi;; ;)"
ClientSocket: url: /8192:0:1:0:0:0:0:0:0:0:

clientsocket: streaming parameters before defaults from config:
clientsocket: reject config default audiolang =
clientsocket: reject config default auth = false
clientsocket: accept config default bframes = 0
clientsocket: accept config default bitrate = 500
clientsocket: reject config default foreground = true
clientsocket: reject config default group =
clientsocket: accept config default level = 3.1
clientsocket: reject config default listen:8002 = 1
clientsocket: reject config default listen:8003 = 1
clientsocket: accept config default profile = baseline
clientsocket: accept config default size = 480p
clientsocket: reject config default webifport = 80

clientsocket: streaming parameters after defaults:
    bframes = 0
    bitrate = 500
    level = 3.1
    profile = baseline
    size = 480p

clientsocket: streaming parameters after url params:
    bframes = 0
    bitrate = 500
    level = 3.1
    profile = baseline
    size = 480p
clientsocket: reject default bitrate, it is already set to 500
clientsocket: reject default size, it is already set to 480p
clientsocket: reject default profile, it is already set to baseline
clientsocket: reject default level, it is already set to 3.1
clientsocket: reject default bframes, it is already set to 0
clientsocket: accept default framerate = 30000

clientsocket: streaming parameters after setting default params:
    bframes = 0
    bitrate = 500
    framerate = 30000
    level = 3.1
    profile = baseline
    size = 480p
Service: create service: 8192:0:1:0:0:0:0:0:0:0:
ClientSocket: default live request
ClientSocket: default live transcoding request
ClientSocket: transcoding service broadcom
LiveTranscodingBroadcom: 8192:0:1:0:0:0:0:0:0:0
WebifRequest: send request to webif: "GET /web/stream?StreamService=8192:0:1:0:0:0:0:0:0:0 HTTP/1.0

"
ClientSocket: http_trap: LiveTranscodingBroadcom: tuning request to enigma failed (webif timeout) (std::exception) (404: HTTP/1.1 404 Not found, cannot tune to service@Content-Type: text/html@Connection: close@Accept-Ranges: bytes@@)

 

enigma2

 

[StreamService] handle command 8192:0:1:0:0:0:0:0:0:0
[StreamService]e execBegin 8192:0:1:0:0:0:0:0:0:0:
[Navigation] recording service: <enigma.eServiceReference; proxy of <Swig Object of type 'eServiceReference *' at 0xb23d72f0> >
[StreamService] RECORD event for us: <enigma.iRecordableServicePtr; proxy of <Swig Object of type 'ePtr< iRecordableService > *' at 0xb23d75d8> >
[eTSMPEGDecoder] decoder state: play, vpid=0001, apid=0001
[eDVBAudio2] AUDIO_SET_BYPASS bypass=1 ok
[eDVBAudio2] AUDIO_PAUSE ok
[eDVBAudio2] AUDIO_PLAY ok
[eDVBVideo] Video Device: /dev/dvb/adapter0/video2
[eDVBVideo2] VIDEO_SET_STREAMTYPE 0 - ok
[eDVBVideo2] VIDEO_FREEZE ok
[eDVBVideo2] VIDEO_PLAY ok
[eDVBVideo2] VIDEO_SLOWMOTION 0 ok
[eDVBVideo2] VIDEO_FAST_FORWARD 0 ok
[eDVBVideo2] VIDEO_CONTINUE ok
[eDVBAudio2] AUDIO_CONTINUE ok
[eServiceHDMIRecord] Recording to ...
[eServiceHDMIRecord] can't open recording file: No such file or directory
[StreamService] RECORD event for us: <enigma.iRecordableServicePtr; proxy of <Swig Object of type 'ePtr< iRecordableService > *' at 0xb23d75d8> >
[StreamService] execEnd 8192:0:1:0:0:0:0:0:0:0:
[eServiceHDMIRecord] stop recording!
[eServiceHDMIRecord] (was not recording)
[eTSMPEGDecoder] decoder state: play, vpid=ffffffff, apid=ffffffff

 

 

Transcoding

 

streamproxy

 

streamproxy: accept new connection on port 8002, default action: transcode, fd 6
ClientSocket: header[accept]: "*/*"
ClientSocket: header[connection]: "close"
ClientSocket: header[host]: "192.168.1.2"
ClientSocket: header[user-agent]: "Enigma2 HbbTV/1.1.1 (+PVR+RTSP+DL;OpenPLi;; ;)"
ClientSocket: url: /8192:0:1:0:0:0:0:0:0:0:?bitrate=2048000&width=1280&height=720&aspectratio=2&interlaced=0

clientsocket: streaming parameters before defaults from config:
clientsocket: reject config default audiolang =
clientsocket: reject config default auth = false
clientsocket: accept config default bframes = 0
clientsocket: accept config default bitrate = 500
clientsocket: reject config default foreground = true
clientsocket: reject config default group =
clientsocket: accept config default level = 3.1
clientsocket: reject config default listen:8002 = 1
clientsocket: reject config default listen:8003 = 1
clientsocket: accept config default profile = baseline
clientsocket: accept config default size = 480p
clientsocket: reject config default webifport = 80

clientsocket: streaming parameters after defaults:
    bframes = 0
    bitrate = 500
    level = 3.1
    profile = baseline
    size = 480p
clientsocket: get parameter[aspectratio] = "2"
clientsocket: reject streaming specific param aspectratio = 2
clientsocket: get parameter[bitrate] = "2048000"
clientsocket: accept streaming specific param bitrate = 2048000
clientsocket: get parameter[height] = "720"
ClientSocket: Xtrend workaround active
clientsocket: accept streaming specific param size = 720p
clientsocket: get parameter[interlaced] = "0"
clientsocket: reject streaming specific param interlaced = 0
clientsocket: get parameter[width] = "1280"
clientsocket: reject streaming specific param width = 1280

clientsocket: streaming parameters after url params:
    bframes = 0
    bitrate = 2048
    level = 3.1
    profile = baseline
    size = 720p
clientsocket: reject default bitrate, it is already set to 2048
clientsocket: reject default size, it is already set to 720p
clientsocket: reject default profile, it is already set to baseline
clientsocket: reject default level, it is already set to 3.1
clientsocket: reject default bframes, it is already set to 0
clientsocket: accept default framerate = 30000

clientsocket: streaming parameters after setting default params:
    bframes = 0
    bitrate = 2048
    framerate = 30000
    level = 3.1
    profile = baseline
    size = 720p
Service: create service: 8192:0:1:0:0:0:0:0:0:0:
ClientSocket: default live request
ClientSocket: default live transcoding request
ClientSocket: transcoding service broadcom
LiveTranscodingBroadcom: 8192:0:1:0:0:0:0:0:0:0
WebifRequest: send request to webif: "GET /web/stream?StreamService=8192:0:1:0:0:0:0:0:0:0 HTTP/1.0

"

 

enigma2

 

[StreamService] handle command 8192:0:1:0:0:0:0:0:0:0
[StreamService]e execBegin 8192:0:1:0:0:0:0:0:0:0:
[Navigation] recording service: <enigma.eServiceReference; proxy of <Swig Object of type 'eServiceReference *' at 0xb23d7230> >
[StreamService] RECORD event for us: <enigma.iRecordableServicePtr; proxy of <Swig Object of type 'ePtr< iRecordableService > *' at 0xb23d74b8> >
[eTSMPEGDecoder] decoder state: play, vpid=0001, apid=0001
[eDVBAudio2] AUDIO_SET_BYPASS bypass=1 ok
[eDVBAudio2] AUDIO_PAUSE ok
[eDVBAudio2] AUDIO_PLAY ok
[eDVBVideo] Video Device: /dev/dvb/adapter0/video2
[eDVBVideo2] VIDEO_SET_STREAMTYPE 0 - ok
[eDVBVideo2] VIDEO_FREEZE ok
[eDVBVideo2] VIDEO_PLAY ok
[eDVBVideo2] VIDEO_SLOWMOTION 0 ok
[eDVBVideo2] VIDEO_FAST_FORWARD 0 ok
[eDVBVideo2] VIDEO_CONTINUE ok
[eDVBAudio2] AUDIO_CONTINUE ok
[eServiceHDMIRecord] Recording to ...
[eServiceHDMIRecord] can't open recording file: No such file or directory
[StreamService] RECORD event for us: <enigma.iRecordableServicePtr; proxy of <Swig Object of type 'ePtr< iRecordableService > *' at 0xb23d74b8> >

 

Is this a limitation of the drivers on the Duo 4K or could it be possibly fixed? Does anyone tried it to see if it works correctly with other Vu 4K models with HDMI input?

An minor observation in case it helps debugging: when Duo 4K is just displaying the HDMI input on the tv (#SERVICE 1:0:1:0:0:0:0:0:0:0:/8192:0:1:0:0:0:0:0:0:0:HDMI-In), if any button is pressed on the webif and a screenshot is created (enigma2 log: [eConsoleAppContainer] Starting /usr/bin/grab) then video goes black and only audio continues. To restart HDMI input, the Duo 4K has to be restarted.

Many thanks to anyone willing to take a look into it.

Do TVs handle HDMI CEC "Forward volume keys" ?

$
0
0

Hi, I've set HDMI CEC "Forward volume keys" but the signals to the TV get ignored. The box sends messages:

 

[eHdmiCEC] send message 44 41

 

[eHdmiCEC] send message 45
[eHdmiCEC] send message 44 42
[eHdmiCEC] send message 45
 
but they have no effect even though the tv does get turned on and off correctly via CEC. As far as I can tell there is no setting for CEC volume key reception on the TV. Is there some way to fix this or is it normal for TVs to not handle this?
 
I have a Zgemma H5 with openpli 6.2 and a Samsung LE37C670.
 
Thanks,

Problem with the weather plugin. Can’t add any location.

$
0
0

Hi , first of all a greetings to the whole community for logging in for first time .

I use OpenPLI 7.2 on Zgemma H9 Combo ; I like and everything is ok , but I can't see the weather info when change the channel .

From panel plugin I istalled wheatherplugin but I can't configure for my city ( and other city ) ; on msn-wheater ok to configure my city and get weather  from plugin but I don't see on infobar .

There is a solution?

Thanks.

Translations for Enigma 2: Please post them here!

$
0
0

Hi,
it would be nice to provide in this thread always the latest translation files of the GUI to be used in the images.

Find attached the german translation file.

 

EDIT: We, as in the OpenPLi team, are still looking for volunteers to help us with the translation!

            Some detailed additional information for our future volunteers. ;)

RTL8811AU wifi

$
0
0

Hello. How to run the wifi adapter realtek RTL8811AU ? On VTI, it was enough to install "enigma2-plugin-drivers-network-usb-rtl8812au - 1.0-r1"

Unfortunately, the card does not appear in the menu after installation.

USB automount doesn't work anymore + VFD clock GSOD

$
0
0
Hi all,

Running OpenPLi 3.0 on VU+ Duo.

After an update two or three days ago, my usb stick fails to automount after a reboot. I have to create the mountpoint manually and run

mount /dev/sda1 /media/usb

The other issue is with permanent VFD clock plugin which causes GSOD. It's rather nasty, because once enabled, it crashed enigma as soon as it's started creating an endless GSOD loop until I manually delete the plugin via ftp.

Thanks for help

Multiboot Mutant HD60

$
0
0
Have a Mutant HD60 with OpenPli 7.2 but want to add 7.3 in slot 2 but I can not find that menu. Do I have to install the recovery image first but what happens to my image in slott 1.

Problem with softcam OpenPli 7

$
0
0
Hi, try to insert Open Pli 7.0 on my Vu + Zero in multiboot. Has ver 6.2 that works. My problem is that I don't think my softcam is staring. Has tried to transfer the settings with the backup file and also a clean new installation from the beginning but the softcam does not start. Look under the blue button that it is installed. How to write the command in telnet to see if is running, and in which directory is the MgCamd file located?
Nierw

Black screen on front panel of VU+ Solo 4K and Ultimo 4K

$
0
0

Dear OpenPLI team,

1) My friend has VU+ Solo 4K and he has problem with front panel. Everything was OK until he tried flashing 7.3 RC and full 7.3 images. Panel is black in standby mode. When loading system he can see only splash screen picture but from time when boot logo is to be loaded and it is visible on TV screen the panel is black again and it stays black on. He tried several skins, some advices from topic about problems with Gigablue but nothing has helped. Returning back to 7.2 image panel runs well.

2) I used OpenPLI 7.3 on two VU+ Ultimo 4K devices satisfactorily for several months but sudenly today I have the same problem as my friend on one of them! Yesterday evening panel was ok till switching box off to standby, today panel is black. And again when starting system only splash screen is visible. I flashed 7.2 backup back and panel runs ok in it.
(I have updated both boxes during yesterday but they have been switched on and off to standby mode several times during day till night. Panels were still ok.)

There must be some mismatch in control of panel in the OpenPLI 7.3 for Solo 4K and maybe some kind of "time bomb" in OpenPLI 7.3 for Ultimo 4K in my case. I do not believe too much that it is caused by yesterday's update. Please try to solve it because I would not like to be frozen with 7.2 and waiting when problem appears in the second one. I would like to continue with progress of OpenPLI image further on.

 

Thanks anyone for any help in advance.


Common interface assignment no more working

$
0
0

Hi,

 

I have the formuler F1.

 

I use an officiel smartcard with oscam and an official CI+ module.

Untill yesterday I could assign which channels have to be read by CI and everything worked fine (CI channels and smartcard channels).

 

I tried today to flash to new openpli 6.1, loading oscam and common interface assignement in the plugins but it did not work anymore.

They work separately (removing CI, smartcard channels work) but if I insert CI module, even if i assigned the channels, stb tries systematically to read info on CI module, and therefore smartcard channels do not work anymore.

 

Even downgrading to an older image, the problem stays.

 

Was it something changed today in the common interface assignment plugin?

 

If no, how could i make it work both again?

 

Sincerely thanks for your help because i'm desperate (working on it for 6 hours with multiple image flashing but without success)

 

 

CI module and oscam

$
0
0

Hi everyone,

 

I have a NEOTION CI module installing in my vu+ Zero 4K. It works fine but I have no logs in Oscam. I wonder if it is possible to run this CI module under oscam.

 

Thanks in advance for your reply.... hoping you could find a solution for me

 

omnikey 3121 & vu duo2

$
0
0

im using openpli 7.2 on duo2 & want to add omni reader

is it possible ?

& how do i make work?

thanks

Greenscreen whenn i want to start record

$
0
0
I have a problem.
When i want to record,choose channel,program and press green button to save,
i have greenscreen at attachment.
 
Do you know how to fix it?

Attached Thumbnails

  • IMG_20201013_071910.jpg

Headless / Server version of OpenPLi?

$
0
0

Hello. I was wondering if a server version of OpenPLi could exist and work.

I'm not sure how much control the openwebif interface I've seen gives, but I thought maybe that could be how it was managed.

The idea is an alternative to TVHeadend. TVHeadend honestly works great... It does so much more than I would ever need, but really falls short for me when it comes to channel mapping and epg mapping. From what I have seen enigma2 and OpenPLi do this much better.

 

Stupid idea? Good idea?

 

 

Viewing all 10561 articles
Browse latest View live


Latest Images

<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>