Hello,
I have the usb dvb RTL2832 with tuner R820T and I have problem to work with VU+ UNO. The same tuner in ET9000 works perfect.
This are the logs:
ET9000
DVB: registering new adapter (dvb0) DVB: registering adapter 0 frontend 0 (DVB-S2)... DVB: registering adapter 0 frontend 1 (DVB-S2)... input: front panel as /devices/virtual/input/input2 NET: Registered protocol family 10 dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (RTL2832U DVB-T USB DEVICE) DVB: registering adapter 1 frontend 0 (Realtek DVB-T RTL2832)... dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected. usbcore: registered new interface driver dvb_usb_rtl2832u
root@et9x00:~# lsmod Module Size Used by dvb_usb_rtl2832 426328 2 dvb_usb 18026 1 dvb_usb_rtl2832 ipv6 351430 12 dvb 5022440 31 modloader2 32629 1 dvb modloader 22281 0 tpm 6509 3 dvb,modloader2,modloader
VU+ UNO
dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (RTL2832U DVB-T USB DEVICE) RTL2832U usb_init_bulk_setting : USB2.0 HIGH SPEED (480Mb/s) RTL2832U check_tuner_type : ERROR Unknown tuner on board... dvb-usb: no frontend was attached by 'RTL2832U DVB-T USB DEVICE' input: IR-receiver inside an USB DVB receiver as /devices/platform/ehci-brcm.1/usb2/2-1/input/input1 dvb-usb: schedule remote query interval to 287 msecs. dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected. usbcore: registered new interface driver dvb_usb_rtl2832u
root@vuuno:~# lsmod Module Size Used by dvb_usb_rtl2832 391387 0 rt2800usb 13121 0 rt2800lib 43443 1 rt2800usb rt2x00usb 10681 1 rt2800usb rt2x00lib 40506 3 rt2800usb,rt2800lib,rt2x00usb mac80211 208171 3 rt2800lib,rt2x00usb,rt2x00lib ipv6 346524 12 fpga_directc 57585 0 brcmfb 1127 3 dvb_bcm7413 5059988 2 fpga_directc,brcmfb procmk 1397 2 fpga_directc,dvb_bcm7413
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=2838 Rev= 1.00 S: Manufacturer=Realtek S: Product=RTL2838UHIDIR S: SerialNumber=00000013 C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=dvb_usb_rtl2832u E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
root@vuuno:~# cat /proc/bus/nim_sockets
NIM Socket 0:
Type: DVB-S2
Name: Vuplus DVB-S NIM
Frontend_Device: 0
Anyone have a idea why this is happening?
Thanks